{"id":10006,"date":"2026-07-23T11:40:04","date_gmt":"2026-07-23T09:40:04","guid":{"rendered":"https:\/\/tusa-precision.ch\/faq\/how-should-aisi-316l-be-drilled-correctly\/"},"modified":"2026-07-23T11:40:04","modified_gmt":"2026-07-23T09:40:04","slug":"how-should-aisi-316l-be-drilled-correctly","status":"publish","type":"faq","link":"https:\/\/tusa-precision.ch\/en\/faq\/how-should-aisi-316l-be-drilled-correctly\/","title":{"rendered":"How should AISI 316L be drilled correctly?"},"content":{"rendered":"<div class=\"faq-block\">\n<h1>How should AISI 316L be drilled correctly?<\/h1>\n<p>Drilling AISI 316L means fighting its greatest enemy: work hardening. The fundamental rule is &#8220;never stop&#8221;. The drill must keep cutting continuously; every hesitation or pause in the hole instantly hardens the material, making further penetration impossible or destructive to the tool. It is essential to use drills with a large point angle (140\u00b0) to improve self-centering and reduce axial thrust, and to ensure perfect chip evacuation through high-pressure internal coolant.   <\/p>\n<h2>Which drills should be used to drill AISI 316L accurately?<\/h2>\n<p>Precision requires rigidity and geometry:<\/p>\n<ul>\n<li><strong>Solid Carbide (VHM)<\/strong>: HSS drills deflect too much. Micrograin K15\/K20 carbide provides the rigidity required for H7\/H8-tolerance holes. <\/li>\n<li>Coating: A heat-resistant TiAlN or AlCrN coating with low friction is essential to avoid adhesion (BUE).<\/li>\n<li><strong>Geometry<\/strong>: Drills with a 4-facet grind or web thinning reduce thrust force and improve centering.<\/li>\n<\/ul>\n<h2>Which drilling parameters are recommended for 316L stainless steel?<\/h2>\n<p>Parametri consigliati per punte VHM 5xD su 316L:<\/p>\n<ul>\n<li><strong>Vc<\/strong>: 60-80 m\/min. Do not exceed this range to avoid burning the cutting edges. <\/li>\n<li><strong>Feed (fn)<\/strong>: 0.08-0.15 mm\/rev, depending on diameter.<\/li>\n<li><strong>Drilling Cycle<\/strong>: Avoid pecking if possible. If required (holes &gt;3xD without through-coolant), peck only occasionally and never allow the drill to rub on the bottom. The tool should re-enter the hole already under feed.  <\/li>\n<\/ul>\n<h2>How can work hardening and overheating be avoided when drilling AISI 316L?<\/h2>\n<p>To prevent thermal and structural damage:<\/p>\n<ul>\n<li><strong>Coolant<\/strong>: Supply 10-12% emulsion internally. The oil reduces friction and the water removes heat. <\/li>\n<li>Pilot Drill: For deep holes (&gt;8xD), always use a short pilot drill (1-2xD) with the same or a slightly larger point angle (e.g. 142\u00b0) to guide entry without vibration.<\/li>\n<li><strong>Exit Control<\/strong>: Reduce feed by 40% in the last few millimeters before breakthrough to avoid a &#8220;cap burr&#8221; and chipping of the drill edges.<\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>How should AISI 316L be drilled correctly? Drilling AISI 316L means fighting its greatest enemy: work hardening. The fundamental rule is &#8220;never stop&#8221;. The drill must keep cutting continuously; every hesitation or pause in the hole instantly hardens the material, making further penetration impossible or destructive to the tool. It is essential to use drills [&hellip;]<\/p>\n","protected":false},"featured_media":0,"menu_order":7,"template":"","meta":{"_acf_changed":false,"rank_math_title":"How should AISI 316L be drilled correctly? | Tusa","rank_math_description":"Drilling AISI 316L means fighting its greatest enemy: work hardening. The fundamental rule is \"never stop\". The drill must keep cutting continuously."},"class_list":["post-10006","faq","type-faq","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq\/10006","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq"}],"about":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/types\/faq"}],"wp:attachment":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/media?parent=10006"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}