{"id":10019,"date":"2026-07-23T11:40:23","date_gmt":"2026-07-23T09:40:23","guid":{"rendered":"https:\/\/tusa-precision.ch\/faq\/how-can-the-finish-on-grade-5-titanium-be-improved\/"},"modified":"2026-07-23T11:40:23","modified_gmt":"2026-07-23T09:40:23","slug":"how-can-the-finish-on-grade-5-titanium-be-improved","status":"publish","type":"faq","link":"https:\/\/tusa-precision.ch\/en\/faq\/how-can-the-finish-on-grade-5-titanium-be-improved\/","title":{"rendered":"How can the finish on Grade 5 titanium be improved?"},"content":{"rendered":"<div class=\"faq-block\">\n<h1>How can the finish on Grade 5 titanium be improved?<\/h1>\n<p>Achieving a mirror-like surface finish (Ra &lt; 0.4 \u00b5m) on Grade 5 titanium (Ti-6Al-4V) requires preventing elastic springback and high-frequency vibration. Titanium tends to &#8220;grab&#8221; the tool; if cutting pressure is not constant, the surface becomes dull and torn. The key is to use finishing cutters with a high flute count (5 or more), high helix angles (45\u00b0 or more) to maintain continuous contact with the workpiece, and climb milling with the correct finishing allowance (at least 0.1-0.2 mm) so that virgin, non-work-hardened material is cut.  <\/p>\n<h2>Which end mill should be used to achieve a good surface finish on Grade 5 titanium?<\/h2>\n<p>Cutter selection is decisive:<\/p>\n<ul>\n<li><strong>Number of Flutes<\/strong>: Use 5, 7, or even 9 flutes. More flutes mean smaller scallop spacing at the same table feed. <\/li>\n<li><strong>Helix Angle<\/strong>: A strong helix (45\u00b0-50\u00b0) reduces initial impact and provides a soft cutting action.<\/li>\n<li><strong>Radius<\/strong>: A corner radius not only improves strength but also distributes surface marks better than a sharp corner.<\/li>\n<\/ul>\n<h2>How can tool marks and vibration be reduced when finishing titanium?<\/h2>\n<p>Common mistakes to avoid:<\/p>\n<ul>\n<li><strong>Dwell<\/strong>: Never stop on the surface. A cutting edge rotating without feed creates chatter marks immediately. <\/li>\n<li><strong>Insufficient Finishing Allowance<\/strong>: If only 0.02 mm is left for finishing, the tool rubs rather than cuts, polishing irregularly and leaving marks.<\/li>\n<li><strong>Vc<\/strong>: For finishing, Vc can be increased (80-100 m\/min) compared with roughing because contact time is short.<\/li>\n<\/ul>\n<h2>Which parameters improve titanium finishing while reducing burrs?<\/h2>\n<p>&#8220;Zero-burr&#8221; parameters:<\/p>\n<ul>\n<li><strong>Smooth Exit<\/strong>: Program an arc-shaped roll-out to prevent the edge from tearing the final strip of material.<\/li>\n<li><strong>Sharp Edges<\/strong>: Use new cutters for the final pass. A cutting edge with wear &gt; 0.05 mm dramatically increases burr formation on titanium. <\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>How can the finish on Grade 5 titanium be improved? Achieving a mirror-like surface finish (Ra &lt; 0.4 \u00b5m) on Grade 5 titanium (Ti-6Al-4V) requires preventing elastic springback and high-frequency vibration. Titanium tends to &#8220;grab&#8221; the tool; if cutting pressure is not constant, the surface becomes dull and torn. The key is to use finishing [&hellip;]<\/p>\n","protected":false},"featured_media":0,"menu_order":16,"template":"","meta":{"_acf_changed":false,"rank_math_title":"How can the finish on Grade 5 titanium be improved? | Tusa","rank_math_description":"Achieving a mirror-like surface finish (Ra < 0.4 \u00b5m) on Grade 5 titanium (Ti-6Al-4V) requires preventing elastic springback and high-frequency vibration."},"class_list":["post-10019","faq","type-faq","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq\/10019","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq"}],"about":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/types\/faq"}],"wp:attachment":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/media?parent=10019"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}