{"id":10020,"date":"2026-07-23T11:40:25","date_gmt":"2026-07-23T09:40:25","guid":{"rendered":"https:\/\/tusa-precision.ch\/faq\/how-can-hole-quality-in-stainless-steel-be-improved\/"},"modified":"2026-07-23T11:40:25","modified_gmt":"2026-07-23T09:40:25","slug":"how-can-hole-quality-in-stainless-steel-be-improved","status":"publish","type":"faq","link":"https:\/\/tusa-precision.ch\/en\/faq\/how-can-hole-quality-in-stainless-steel-be-improved\/","title":{"rendered":"How can hole quality in stainless steel be improved?"},"content":{"rendered":"<div class=\"faq-block\">\n<h1>How can hole quality in stainless steel be improved?<\/h1>\n<p>La qualit\u00e0 del foro su acciaio inossidabile (cilindricit\u00e0, rugosit\u00e0 e assenza di bava) dipende dalla stabilit\u00e0 di centraggio e dalla gestione termica. Le punte standard tendono a &#8220;vagare&#8221; (walk) all&#8217;ingresso su superfici inox dure, creando fori leggermente ovalizzati o fuori asse. La soluzione \u00e8 utilizzare punte in metallo duro con affilatura a 4 facce o geometria autocentrante, precedute da una centrinatura o, meglio ancora, da una punta pilota dello stesso diametro (o leggermente maggiore per l&#8217;angolo) se il foro \u00e8 profondo.  <\/p>\n<h2>How can clean, burr-free holes be produced in stainless steel?<\/h2>\n<p>For H7\/H8 tolerances directly from drilling:<\/p>\n<ul>\n<li><strong>Spindle Run-out<\/strong>: Must be &lt;5 microns. High run-out causes the drill to &#8220;ream&#8221; the hole and oversize it. <\/li>\n<li><strong>3-Flute Drills<\/strong>: For short holes (&lt;3xD), 3-flute drills provide better roundness and surface finish through triple guidance.<\/li>\n<li><strong>Margins<\/strong>: Double margins burnish the hole wall and improve Ra.<\/li>\n<\/ul>\n<h2>Which drills ensure tight tolerances in stainless steel?<\/h2>\n<p>Work hardening: the enemy of stainless steel.<\/p>\n<ul>\n<li>Do Not Hesitate: Entry and feed must be decisive. Feed that is too low (e.g. &lt; 0.03 mm\/rev) causes immediate work hardening at the bottom. <\/li>\n<li><strong>Pecking<\/strong>: Avoid it. Every time the drill re-enters, it impacts a work-hardened layer. If necessary, reduce the retraction distance and use chip breaking without fully leaving the hole.  <\/li>\n<\/ul>\n<h2>How can work hardening be avoided when drilling stainless steel?<\/h2>\n<p>Anti-burr exit strategies:<\/p>\n<ul>\n<li><strong>Discs<\/strong>: 316 stainless tends to form a &#8220;cap&#8221; at exit that does not detach.<\/li>\n<li><strong>Technique<\/strong>: Reduce feed by 50% over the last 0.5-1 mm of drilling. This reduces axial thrust that would otherwise push through the material instead of cutting it. <\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>How can hole quality in stainless steel be improved? La qualit\u00e0 del foro su acciaio inossidabile (cilindricit\u00e0, rugosit\u00e0 e assenza di bava) dipende dalla stabilit\u00e0 di centraggio e dalla gestione termica. Le punte standard tendono a &#8220;vagare&#8221; (walk) all&#8217;ingresso su superfici inox dure, creando fori leggermente ovalizzati o fuori asse. La soluzione \u00e8 utilizzare punte [&hellip;]<\/p>\n","protected":false},"featured_media":0,"menu_order":17,"template":"","meta":{"_acf_changed":false,"rank_math_title":"How can hole quality in stainless steel be improved? | Tusa","rank_math_description":"Hole quality in stainless steel (cylindricity, roughness, and absence of burrs) depends on centering stability and thermal management."},"class_list":["post-10020","faq","type-faq","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq\/10020","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq"}],"about":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/types\/faq"}],"wp:attachment":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/media?parent=10020"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}