{"id":10023,"date":"2026-07-23T11:40:32","date_gmt":"2026-07-23T09:40:32","guid":{"rendered":"https:\/\/tusa-precision.ch\/faq\/how-can-stable-microholes-be-produced-in-hard-steels\/"},"modified":"2026-07-23T11:40:32","modified_gmt":"2026-07-23T09:40:32","slug":"how-can-stable-microholes-be-produced-in-hard-steels","status":"publish","type":"faq","link":"https:\/\/tusa-precision.ch\/en\/faq\/how-can-stable-microholes-be-produced-in-hard-steels\/","title":{"rendered":"How can stable microholes be produced in hard steels?"},"content":{"rendered":"<div class=\"faq-block\">\n<h1>How can stable microholes be produced in hard steels?<\/h1>\n<p>Microdrilling (\u00d8 &lt; 1 mm) in hardened steels (&gt; 50 HRC) is a stability challenge. The microdrill bends under very small loads (buckling). Stability is achieved by eliminating any run-out error (target &lt; 2 microns) and using micrograin carbide drills specifically designed for hard materials (Hard Drilling), with a reinforced core. The stronger core reduces chip space, so chip evacuation must be carefully managed.  <\/p>\n<h2>Which micro drill should be selected for microdrilling hard steels?<\/h2>\n<p>The hard-material microdrill:<\/p>\n<ul>\n<li>Point Angle: Often 135\u00b0 or 140\u00b0.<\/li>\n<li><strong>Coating<\/strong>: TiSiN or AlTiSiN resistant to red heat.<\/li>\n<li><strong>Shank Tolerance<\/strong>: h4 or h5 for perfect fit in hydraulic or shrink-fit holders.<\/li>\n<\/ul>\n<h2>How can micro-drill breakage be avoided during microdrilling?<\/h2>\n<p>Immediate breakage? Main causes: <\/p>\n<ul>\n<li><strong>Run-out<\/strong>: Even 5 microns of error makes the drill rotate off-axis, causing immediate cyclic-fatigue failure at entry.<\/li>\n<li><strong>Impact<\/strong>: Entry must be gentle. Reduce entry feed. <\/li>\n<\/ul>\n<h2>Which parameters improve stability and accuracy in microholes?<\/h2>\n<p>Hard-drilling process:<\/p>\n<ul>\n<li><strong>No Deep Pecking<\/strong>: At high HRC, traditional pecking chips the cutting edges. Prefer continuous drilling for limited depths or &#8220;micro-pecking&#8221; that only breaks the chip without fully retracting. <\/li>\n<li><strong>Pilot Hole<\/strong>: Mandatory for holes &gt; 5-6xD. The pilot must have a point angle &gt; greater than the long drill (e.g. 140\u00b0 pilot, 135\u00b0 long drill) so the margins do not contact before the tip. <\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>How can stable microholes be produced in hard steels? Microdrilling (\u00d8 &lt; 1 mm) in hardened steels (&gt; 50 HRC) is a stability challenge. The microdrill bends under very small loads (buckling). Stability is achieved by eliminating any run-out error (target &lt; 2 microns) and using micrograin carbide drills specifically designed for hard materials (Hard [&hellip;]<\/p>\n","protected":false},"featured_media":0,"menu_order":20,"template":"","meta":{"_acf_changed":false,"rank_math_title":"How can stable microholes be produced in hard steels? | Tusa","rank_math_description":"Microdrilling (\u00d8 < 1 mm) in hardened steels (> 50 HRC) is a stability challenge. The microdrill bends under very small loads (buckling)."},"class_list":["post-10023","faq","type-faq","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq\/10023","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq"}],"about":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/types\/faq"}],"wp:attachment":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/media?parent=10023"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}