{"id":9975,"date":"2026-07-23T11:39:56","date_gmt":"2026-07-23T09:39:56","guid":{"rendered":"https:\/\/tusa-precision.ch\/faq\/how-can-vibration-be-avoided-when-milling-stainless-steel\/"},"modified":"2026-07-23T11:39:56","modified_gmt":"2026-07-23T09:39:56","slug":"how-can-vibration-be-avoided-when-milling-stainless-steel","status":"publish","type":"faq","link":"https:\/\/tusa-precision.ch\/en\/faq\/how-can-vibration-be-avoided-when-milling-stainless-steel\/","title":{"rendered":"How can vibration be avoided when milling stainless steel?"},"content":{"rendered":"<div class=\"faq-block\">\n<h1>How can vibration be avoided when milling stainless steel?<\/h1>\n<p>Milling stainless steels (300 series, Duplex, PH) is critical because of their tendency to work harden and their low thermal conductivity. Vibration (chatter) starts when the tool &#8220;bounces&#8221; on the work-hardened surface instead of penetrating it. <\/p>\n<p>To avoid vibration, maximum rigidity of the machine-tool system is essential, along with dedicated cutters featuring variable pitch and variable helix. These geometries break regenerative harmonics, preventing vibration from resonating with the natural frequency of the structure. <\/p>\n<h2>Why does chatter occur when milling stainless steel?<\/h2>\n<p>Chatter in stainless steel develops through a vicious cycle:<\/p>\n<ul>\n<li><strong>Material Elasticity<\/strong>: Stainless steel exhibits springback, pushing the tool away from the workpiece.<\/li>\n<li><strong>Work Hardening<\/strong>: If the tool rubs, even by only a few microns, without cutting, the surface becomes very hard. On the next pass, the tool encounters varying resistance that triggers instability. <\/li>\n<li><strong>High Cutting Forces<\/strong>: The toughness of stainless steel requires high cutting forces, placing heavy demands on spindle rigidity.<\/li>\n<\/ul>\n<h2>Which parameters reduce vibration and chatter in stainless steels?<\/h2>\n<p>To stabilize cutting in stainless steel:<\/p>\n<ul>\n<li><strong>Decisive Feed (fz)<\/strong>: Do not be too conservative. fz must be high enough to penetrate the work-hardened layer (typically &gt; 0.04 mm\/tooth even on small diameters). <\/li>\n<li><strong>Moderate Cutting Speed (Vc)<\/strong>: Keep Vc lower than for carbon steels (e.g. 60-100 m\/min for austenitic stainless steels) to control heat, but high enough to avoid BUE.<\/li>\n<li><strong>Depth (ap\/ae)<\/strong>: Prefer deep axial cuts (high ap) with low radial engagement (low ae) so that forces are directed axially toward the spindle, where the system is stiffer.<\/li>\n<\/ul>\n<h2>Which end-mill geometry helps reduce vibration in stainless steel?<\/h2>\n<p>Geometry makes the difference:<\/p>\n<ul>\n<li><strong>Variable Pitch<\/strong>: Irregular tooth spacing breaks the periodic excitation frequency.<\/li>\n<li><strong>Variable Helix Angle<\/strong>: (e.g. 35\u00b0\/38\u00b0) changes the impact angle of each tooth, stabilizing the cut. <\/li>\n<li><strong>Positive Rake<\/strong>: A pronounced positive rake reduces cutting pressure and heat, helping prevent work hardening.<\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>How can vibration be avoided when milling stainless steel? Milling stainless steels (300 series, Duplex, PH) is critical because of their tendency to work harden and their low thermal conductivity. Vibration (chatter) starts when the tool &#8220;bounces&#8221; on the work-hardened surface instead of penetrating it. To avoid vibration, maximum rigidity of the machine-tool system is [&hellip;]<\/p>\n","protected":false},"featured_media":0,"menu_order":4,"template":"","meta":{"_acf_changed":false,"rank_math_title":"How can vibration be avoided when milling stainless steel? | Tusa","rank_math_description":"Milling stainless steels (300 series, Duplex, PH) is critical because of their tendency to work harden and their low thermal conductivity."},"class_list":["post-9975","faq","type-faq","status-publish","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq\/9975","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/faq"}],"about":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/types\/faq"}],"wp:attachment":[{"href":"https:\/\/tusa-precision.ch\/en\/wp-json\/wp\/v2\/media?parent=9975"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}